Hi all,
just installed, what does show the TThrottle column??
Quote from: Corsair on November 27, 2009, 06:36:42 PM
Hi all,
just installed, what does show the TThrottle column??
The amount of throttling. 0 (gone) = not throttling.
Quote from: fred on November 27, 2009, 06:40:48 PM
Quote from: Corsair on November 27, 2009, 06:36:42 PM
Hi all,
just installed, what does show the TThrottle column??
The amount of throttling. 0 (gone) = not throttling.
in the computer that I've installed BT is showing 30 when TThrottle is showing around 70
the temperature is the same.
but the tthrottle is only shown in the "server" computer, not the "hosts"
Quote from: Corsair on November 27, 2009, 06:47:41 PM
Quote from: fred on November 27, 2009, 06:40:48 PM
Quote from: Corsair on November 27, 2009, 06:36:42 PM
Hi all,
just installed, what does show the TThrottle column??
The amount of throttling. 0 (gone) = not throttling.
in the computer that I've installed BT is showing 30 when TThrottle is showing around 70
the temperature is the same.
but the tthrottle is only shown in the "server" computer, not the "hosts"
TThrottle gives the running % while BoincTasks gives the throttled %.
70 TThrottle = 70% running = 30 BoincTasks = 30% throttled.
BoincTasks value = 100 - TThrottle value
The throttle is not shown when it is 0 = running full (throttle).
I've not managed to let my BT 0.30 show any temperature or throttle states in their columns. How to set the communication up? In TThrottle, BT checkbox is enabled.
Quote from: Pepo on November 28, 2009, 09:58:51 PM
I've not managed to let my BT 0.30 show any temperature or throttle states in their columns. How to set the communication up? In TThrottle, BT checkbox is enabled.
http://www.efmer.eu/boinc/boinc_tasks/manual.html (http://www.efmer.eu/boinc/boinc_tasks/manual.html) Check the chapter TThrottle and let me know if it enough to get things working.
Quote from: fred on November 29, 2009, 09:45:39 AM
Quote from: Pepo on November 28, 2009, 09:58:51 PM
I've not managed to let my BT 0.30 show any temperature or throttle states in their columns. How to set the communication up? In TThrottle, BT checkbox is enabled.
http://www.efmer.eu/boinc/boinc_tasks/manual.html (http://www.efmer.eu/boinc/boinc_tasks/manual.html) Check the chapter TThrottle and let me know if it enough to get things working.
I've somehow overlooked the "Extra->Settings -> general tab -> Connect to TThrottle" checkbox.
Thanks.
I'm running a non-CPU-intensive QCN. BT is showing it being throttled by 101%. A bit off ;) 100% should be enough, it even consumed some 36 seconds over the last 3 days - approx. 0.01%, so the throttling should not exceed 99.993...% ;D
OK, I've excluded the QCN apps from throttling, so ti should be a round 100% or 0%. Left to be explained.
I'll check it a few hours ago after connecting it to the quake sensor, it should be then consuming a few CPU%.
In the history, what does the "Reported: Ok (u)" mean?
malariacontrol.net 6.24 malariacontrol.net wu_65_30_251913_0_1259177407 08:55:50 (04:51:09) 26.11.2009 5:51:26 26.11.2009 5:51:38 Reported: Ok (u)
Quote from: Pepo on November 30, 2009, 09:38:15 AM
In the history, what does the "Reported: Ok (u)" mean?
malariacontrol.net 6.24 malariacontrol.net wu_65_30_251913_0_1259177407 08:55:50 (04:51:09) 26.11.2009 5:51:26 26.11.2009 5:51:38 Reported: Ok (u)
An extra check (u) means upload. The task is only seen while uploading and was not seen as waiting to report.
When a task reports in immediately and asks for new work ,the task is gone before BoincTasks can see it as waiting to report.
in tasks tab, right click and suspend and looks like that nothing happens.
when in projects tab you suspend one project, in the task view it's shown as
"waiting to run" or "ready to start" instead as "suspended by user"
Quote from: Corsair on November 30, 2009, 03:14:35 PM
in tasks tab, right click and suspend and looks like that nothing happens.
when in projects tab you suspend one project, in the task view it's shown as
"waiting to run" or "ready to start" instead as "suspended by user"
Yep, I expected more troubles, but these are the only things right now.
The suspended by user is a question of taste, the state stays as it actually is.
But for about 2 weeks I'm busy with my hiking site. So I will be finished before my next hiking trip. ;D
I will only do these two or other bugs that show up.
I have just tried to install BT 0.30. Norton 360 Sonar detected it as a risk and quarantined the installation file (the file downloaded from efmer). Previous installations have worked ok.
Quote from: Dave_In_Melb on December 01, 2009, 07:49:09 PM
I have just tried to install BT 0.30. Norton 360 Sonar detected it as a risk and quarantined the installation file (the file downloaded from efmer). Previous installations have worked ok.
You can:
A) Wait for the next version.
B) Tell me what version you are using 32 of 64. And I need to know: Name of detection given by Symantec. So I can file a false positive.
https://submit.symantec.com/dispute/false_positive/ (https://submit.symantec.com/dispute/false_positive/)