Messages

Finally made 1st version of Croatian translation of a file. As there is no github, so adding it on server here:

https://file.io/rhQUt7Kor31A

This should last for a year to be downloaded.

Noticed also, that the system only shows 1 logical nvidia & 1 physical nvidia. See image here:

https://imgur.com/a/Ml6GLiN

While I have 3 cards in my system:

https://imgur.com/GHFGAij

Tested v7.78, seems stable. Works OK on 2x12c / 2x24t.

Suggestion: if the program can't run more then 32c, can you post only "core temps" & ignore the "thread temps"? This would give more accurate picture of working conditions of CPU.

Thanks

32 is as far as I can go.
Above 32 I have to rewrite the driver and that's very expensive, probably in the thousands of dollars.
Microsoft made it much more difficult to add drivers.

Fred

Here is a wild question, OK 32 is a limit. But can it be that you make 32 throttles limit for single CPU?

So you would on dual-CPU systems work on single driver for CPU, making it with 2x32?

Selecting GPU-1 or GPU-2, always gives me only single option for GPU. Can't add more on v7.7.2

But Beta v7.7.8 works OK so far, all 3 temps present of all 3 GPUs.

Updated to 7.74 that supports 32 temperature cores.

Started to test this Beta v7.7.8, after the summer is over. (Sorry, catched this message too late.)

In Temperature sheet, there are most of the cores written (32 out of now 48) & all 3 GPUs. Previously v7.7.2 did not support GPU at all & had to run Tech Power-up to keep track of temperature on Teslas. 

Will write more, as this needs to be tested on 24/7 basis. 

Hi, they do detect more than 1 GPU...but only show temps from 1 GPU, one or the other. 

So no luck here.

Well, given that more & more systems use more cores...maybe you can gives us a suggestion how to send you back some data & this gets updated? 🤷‍♂️

Using GPU-Z will not work, as it will show only SINGLE card & can't monitor multiple cards.

Tried that, but the thermal management is only available for a single card. 

Using GPU-Z 2.43.0 with Tthrottle v7.72 on Win10 x64.

Hi all,
also, as I do have 2 cards in my system, both of them are detected & shown in Loggin sheet, with both temperatures detected.

But on Program sheet, no GPU is shown detected - only 0°C is shown in GPU detection. What is the deal with that? How to come over it? Has anybody had similar issue?

Thanks,

Hi all,
as I do have 2x Deca-core (10 core) system in my Workstation, so total number of my cores is actually 20 (or 40 threads). As that is more then 16, so the Temperature sheet & Graph sheets do not work. Does anybody else have a similar problem?

Thank,

Hi,
would you mind if I send you some Gridcoins, as your program has saved my GPUs & CPUs several times.

Just post an address & I'll send it to you.

Thanks,

Which can also be understood in most of ex-YU, so: Croatia, Bosnia & Hercegovina, Montenegro, Serbia, Kosovo...just let me know & mail me a form to translate! 

7.22 ver also makes the BSOD...all on cputemperature.sys

which version do u suggest for an old WinXP system?

The problem is the CPU driver, so it will never work.

Also, could a 2 processor system be blamed for BSOD with cputemperature.sys ?

'cause BP6 has a 2 processors: http://www.tomshw.it/guides/hardware/cpu/20041220/images/abit_bp6_big.jpg

OK...so the TThrottle needs a P4 processor or newer to work...'cause of the CPU temp sensor!

thx